Proud ally of:

Trade

 

Classes available for Trade

 

Sheet Metal 2 (Hands-On)

This course consists of 159 classroom hours covering the following areas: Safety Review; Trade Math 104; Shop Production and Organization; Installation of Air Distribution Accessories; Air Systems; Duct Fabrication Standards; Introduction to Layout; Fabrication I – Parallel Line Development; Fabrication II – Radial Line Development; and Hands-on Shop Fabrication.

September 8, 2026 – 5:30 – 8:30 PM – Tuesdays & Thursdays

ABC Member: $2,817.00 / Not Yet A Member: $3,360.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

MARTHA'S VINEYARD

Sheet Metal 2 Daytime (Hands-On)

This course consists of 152 classroom hours covering the following areas: Safety Review; Trade Math 104; Shop Production and Organization; Installation of Air Distribution Accessories; Air Systems; Duct Fabrication Standards; Introduction to Layout; Fabrication I – Parallel Line Development; Fabrication II – Radial Line Development; and Hands-on Shop Fabrication.

Begins September 18, 2026 – 7:30AM – 3:30 PM – Every other Friday

ABC Member: $2,817.00 / Not Yet A Member: $3,360.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

This will be a hands-on training course. The extra cost is for materials.

Locations:

BILLERICA - GCI TRAINING FACILITY

Sheet Metal 5 (Hands On) – (Begins January 2027)

This course consists of 152 classroom hours covering the following areas: Trade Math – Estimating; Fume Exhaust Design; Introduction to Welding, Brazing and Cutting; Advanced Architectural Sheet Metal; Hands-on Shop Fabrication; and Exam Review and Preparation.

Begins January 2027 – 5:00 – 9:00 PM – Mondays & Wednesdays

ABC Member: $2,817.00 / Not Yet A Member: $3,360.00

*Schedule Update: Sheet Metal classes at our Billerica location will be held two nights per week for 4 hours per night with a shop sessions being scheduled on some Saturdays throughout the course. We will also hold classes during February and April school vacations.

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

This will be a hands-on training course. The extra cost is for materials.

Locations:

BILLERICA - GCI TRAINING FACILITY

Sheet Metal 4 (Hands-On) – (Begins January 2027)

This course consists of 152 classroom hours covering the following areas: Massachusetts Uniform Sheet Metal Code; Trade Math III – Field Measuring; Comprehensive Plan and Specification Reading; Soldering; Architectural Sheet Metal; Louvers, Dampers and Access Doors; Fabrication IV – Comprehensive Review; and Hands-on Shop Fabrication.

Begins January 2027 – 5:00 – 9:00 PM

ABC Member: $2,817.00 / Not Yet A Member: $3,360.00

*Schedule Update: Sheet Metal classes at our Billerica location will be held two nights per week for 4 hours per night with a shop sessions being scheduled on some Saturdays throughout the course. We will also hold classes during February and April school vacations.

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

This will be a hands-on training course. The extra cost is for materials.

Locations:

BILLERICA - GCI TRAINING FACILITY

Sheet Metal 2 (Hands-On) – (Begins January 2027)

This course consists of 152 classroom hours covering the following areas: Safety Review; Trade Math 104; Shop Production and Organization; Installation of Air Distribution Accessories; Air Systems; Duct Fabrication Standards; Introduction to Layout; Fabrication I – Parallel Line Development; Fabrication II – Radial Line Development; and Hands-on Shop Fabrication.

Begins January 2027 – 5:00 – 9:00 PM

ABC Member: $2,817.00 / Not Yet A Member: $3,360.00

*Schedule Update: Sheet Metal classes at our Billerica location will be held two nights per week for 4 hours per night with a shop sessions being scheduled on some Saturdays throughout the course. We will also hold classes during February and April school vacations.

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

This will be a hands-on training course. The extra cost is for materials.

Locations:

BILLERICA - GCI TRAINING FACILITY

Sheet Metal 1 (Begins January 2027)

This course consists of 152 classroom hours covering the following areas: Introduction to Sheet Metal; Basic Safety; Introduction to Hand Tools; Introduction to Power Tools; Introduction to B.G.L. c 112 s 237-251 and 271 CMR; Basic Rigging; Introduction to Materials Handling; Basic Communication Skills; Basic Employability Skills; Introduction to Construction Math; Introduction to Construction Drawings; Tools of the Trade; Installation of Ductwork.

Begins January 2027 – 5:00 – 9:00 PM

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

*Schedule Update: Sheet Metal classes at our Billerica location will be held two nights per week for 4 hours per night with a shop sessions being scheduled on some Saturdays throughout the course. We will also hold classes during February and April school vacations.

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

BILLERICA - GCI TRAINING FACILITY

Plumbing Tier 2

This course consists of 120 classroom hours covering the following areas: Drainage, Building Sanitary Waste and Venting System, Allowable Materials and Approval Procedures, Plumbing Traps, Cleanouts, Plumbing Code, Potable Water Supply, Math, Gasfitting, Blueprint Reading & Definitions.

Begins September 9, 2026 – 4PM – 7PM – Mondays & Wednesdays

Tuition: $1,924.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

SPRINGFIELD - SPRINGFIELD TECHNICAL COMMUNITY COLLEGE

Sheet Metal 5 (Hands On)

This course consists of 152 classroom hours covering the following areas: Trade Math – Estimating; Fume Exhaust Design; Introduction to Welding, Brazing and Cutting; Advanced Architectural Sheet Metal; Hands-on Shop Fabrication; and Exam Review and Preparation.

September 9, 2026 – 5:00 – 9:00 PM – Mondays & Wednesdays

ABC Member: $2,817.00 / Not Yet A Member: $3,360.00

*Schedule Update: Sheet Metal classes at our Billerica location will be held two nights per week for 4 hours per night with a shop sessions being scheduled on some Saturdays throughout the course. We will also hold classes during February and April school vacations.

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

This will be a hands-on training course. The extra cost is for materials.

Locations:

BILLERICA - GCI TRAINING FACILITY

Pipefitting 3

This course consists of 159 classroom hours covering the following areas: Steam Traps; In-Line Specialties; Special Piping; Hot Taps; Introduction to Hydronic Systems; Commercial Hydronic Systems; Steam Systems; Water Treatment; Energy Conservation Equipment; ASME Piping Codes for HVAC, Power and Process Piping 7.5; Semiconductor/Hazardous Gas Piping Systems 12.5;  Biopharma Piping Systems 12.5; Orbital Welding Fabrication 15; Chemical/Corrosion Resistant Piping Systems 15; Compressed Air Piping Systems

Begins September 8, 2026 – 5:00 – 8:00 PM – Tuesdays & Thursdays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

 

Locations:

TAUNTON – BRISTOL-PLYMOUTH REGIONAL TECHNICAL SCHOOL

Sheet Metal 3 (Hands-On)

Though this course is held in New Hampshire, the curriculum is for a Massachusetts Journeyman License.

This course consists of 159 classroom hours covering the following areas: Trade Math II; Introduction to Supervisory Skills; Air Properties and Distribution; Principles of Airflow; Air Testing and Balancing; Fabrication III – Triangulation; Plans and Specifications; and Hands-on Shop Fabrication.

Begins September 8, 2026 – 5:30 PM – 8:30 PM – Tuesdays & Thursdays

ABC Member: $2,817.00 / Not Yet A Member: $3,360.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

This will be a hands-on training course. The extra cost is for materials.

Locations:

MANCHESTER NH - OSHA TRAINING INSTITUTE EDUCATION CENTER

Plumbing Tier 1

This course consists of 120 classroom hours covering the following areas: Basic Safety; Introduction to Construction Math; Introduction to Hand Tools; Introduction to Power Tools; Introduction to Construction Drawings; Basic Rigging; Basic Communication Skills; Basic Employability Skills; Introduction to Materials Handling; Introduction to Plumbing; Plumbing Safety; Tools of the Plumbing Trade; Introduction to Plumbing Math; Introduction to Plumbing Drawings; Plastic Pipe and Fittings; Copper Tube and Fittings; Cast-Iron Pipe and Fittings; Carbon Steel Pipe and Fittings; Introduction to Plumbing Fixtures; Introduction to Drain, Waste, and Vent (DWV) Systems.

Begins September 9, 2026 – 5:30 PM – 8:30 PM – Mondays & Wednesdays

Tuition: $1,924.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

NORTH ADAMS – McCANN TECHNICAL SCHOOL

Plumbing Tier 3

This course consists of 120 classroom hours covering the following areas: Applied Math; Sizing and Protecting the Water Supply System; Potable Water Supply Treatment; Types of Venting; Sizing DWV and Storm Systems; Sewage Pumps and Sump Pumps; Corrosive-Resistant Waste Piping; Compressed Air; Service Plumbing.

Begins September 9, 2026 – 5:30 PM – 8:30 PM – Mondays & Wednesdays

Tuition: $1,924.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

NORTH ADAMS – McCANN TECHNICAL SCHOOL

Electrical 4

This course consists of 159 classroom hours and practical application covering the following areas: Load Calculations –Feeders and Services; Health Care Facilities; Standby and Emergency Systems; Basic Electronic Theory; Fire Alarm Systems; Specialty Transformers; Advanced Controls; HVAC Controls; Heat Tracing and Freeze Protection; Motor Operation and Maintenance; Medium-Voltage Terminations/Splices; Special Locations; Fundamentals of Crew Leadership. It is required that all students bring a copy of the National Electrical Code, 2026 Edition, with the Commonwealth of Massachusetts Amendments (527 CMR 12.00) to class.

Begins September 8, 2026
5:00 PM – 8:00 PM – Tuesdays & Thursdays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

BILLERICA - GCI TRAINING FACILITY

Electrical 3

This course consists of 159 classroom hours and practical application covering the following areas: Load Calculations – Branch and Feeder Circuits; Conductor Selection and Calculations; Practical Applications of Lighting; Hazardous Locations; Overcurrent Protection; Distribution Equipment; Transformers; Commercial Electrical Services; Motor Calculations; Voice, Data, and Video; Motor Controls. It is required that all students bring a copy of the National Electrical Code, 2026 Edition, with the Commonwealth of Massachusetts Amendments (527 CMR 12.00) to class.

Begins September 9, 2026

5:00 PM – 8:00 PM – Mondays & Wednesdays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

BILLERICA - GCI TRAINING FACILITY

Electrical 2

This course consists of 159 classroom hours covering the following areas: Alternating Current; Motors: Theory and Application; Electric Lighting; Conduit Bending; Pull and Junction Boxes; Conductor Installations; Cable Tray; Conductor Terminations and Splices; Grounding and Bonding; Circuit Breakers and Fuses; Control Systems and Fundamental Concepts. It is required that all students bring a copy of the National Electrical Code, 2026 Edition, with the Commonwealth of Massachusetts Amendments (527 CMR 12.00) to class.

Begins September 9, 2026
5:00 PM – 8:00 PM – Mondays & Wednesdays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

BILLERICA - GCI TRAINING FACILITY

Electrical 1

This course consists of 159 classroom hours covering the following areas: Basic Safety; Introduction to Construction Math; Introduction to Hand Tools; Introduction to Power Tools; Introduction to Construction Drawings; Basic Rigging; Basic Communication Skills; Basic Employability Skills; Introduction to Materials Handling; Orientation to the Electrical Trade; Electrical Safety; Introduction to Electrical Circuits; Electrical Theory; Introduction to the National Electrical Code (NEC); Device Boxes; Hand Bending; Raceways and Fittings; Conductors and Cables; Basic Electrical Construction Drawings; Residential Electrical Services; Electrical Test Equipment. It is required that all students bring a copy of the National Electrical Code, 2026 Edition, with the Commonwealth of Massachusetts Amendments (527 CMR 12.00) to class.

Begins September 9, 2026 – 5:00 – 8:00 PM – Mondays & Wednesdays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

BILLERICA - GCI TRAINING FACILITY

Sprinklerfitting 2 – ONLINE COURSE

This course consists of 160 classroom hours covering the following areas: Hangers, Supports, Restraints, and Guides; General Purpose Valves; General Trade Math; Shop Drawings; Standard Spray Fire Sprinklers; Wet Fire Sprinkler Systems; Dry-Pipe Systems.

Begins September 8, 2026 – 5:00 – 9:00 PM – Tuesdays

ABC Member: $2,567.00 / Not Yet A Member: $3,360.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

VIRTUAL TRADE COURSE

Sprinklerfitting 3 – ONLINE COURSE

This course consists of 159 classroom hours covering the following areas: Deluge Preaction Systems; Standpipes; Water Supplies; Fire Pumps; Application-Specific Sprinklers and Nozzles.

September 10, 2026 – 5:00 – 8:00 PM – Thursdays

ABC Member: $2,567.00 / Not Yet A Member: $3,360.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

VIRTUAL TRADE COURSE

Sheet Metal 5 (Hands-On)

This course consists of 159 classroom hours covering the following areas: Trade Math – Estimating; Fume Exhaust Design; Introduction to Welding, Brazing and Cutting; Advanced Architectural Sheet Metal; Hands-on Shop Fabrication; and Exam Review and Preparation.

September 8, 2026 – 5:00 – 8:00 PM // Tuesdays & Thursdays

ABC Member: $2,817.00 / Not Yet A Member: $3,360.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

This will be a hands-on training course. The extra cost is for materials.

Locations:

TAUNTON – BRISTOL-PLYMOUTH REGIONAL TECHNICAL SCHOOL

Sheet Metal 3 (Hands-On)

This course consists of 159 classroom hours covering the following areas: Trade Math II; Introduction to Supervisory Skills; Air Properties and Distribution; Principles of Airflow; Air Testing and Balancing; Fabrication III – Triangulation; Plans and Specifications; and Hands-on Shop Fabrication.

September 8, 2026 – 5:00 – 8:00 PM – Tuesdays & Thursdays

ABC Member: $2,817.00 / Not Yet A Member: $3,360.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

This will be a hands-on training course. The extra cost is for materials.

Locations:

TAUNTON – BRISTOL-PLYMOUTH REGIONAL TECHNICAL SCHOOL

Sheet Metal 4 (Hands-On)

This course consists of 159 classroom hours covering the following areas: Massachusetts Uniform Sheet Metal Code; Trade Math III – Field Measuring; Comprehensive Plan and Specification Reading; Soldering; Architectural Sheet Metal; Louvers, Dampers and Access Doors; Fabrication IV – Comprehensive Review; and Hands-on Shop Fabrication.

September 9, 2026 – 5:30 – 8:30 PM // Mondays & Wednesdays

Tuition: $2,258.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

This will be a hands-on training course. The extra cost is for materials.

Locations:

NORTH ADAMS – McCANN TECHNICAL SCHOOL

Sheet Metal 4 (Hands-On)

This course consists of 159 classroom hours covering the following areas: Massachusetts Uniform Sheet Metal Code; Trade Math III – Field Measuring; Comprehensive Plan and Specification Reading; Soldering; Architectural Sheet Metal; Louvers, Dampers and Access Doors; Fabrication IV – Comprehensive Review; and Hands-on Shop Fabrication.

Begins September 8, 2026 – 5:30 – 8:30 PM – Tuesdays & Thursdays

ABC Member: $2,817.00 / Not Yet A Member: $2,360.00

All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

This will be a hands-on training course. The extra cost is for materials.

Locations:

MANCHESTER NH - OSHA TRAINING INSTITUTE EDUCATION CENTER

Sheet Metal 2 (Hands-On)

Though this course is held in New Hampshire, the curriculum is for a Massachusetts Journeyman License.

This course consists of 159 classroom hours covering the following areas: Safety Review; Trade Math 104; Shop Production and Organization; Installation of Air Distribution Accessories; Air Systems; Duct Fabrication Standards; Introduction to Layout; Fabrication I – Parallel Line Development; Fabrication II – Radial Line Development; and Hands-on Shop Fabrication.

Begins September 9, 2026 – 5:30 PM – 8:30 PM – Mondays & Wednesdays

ABC Member: $2,817.00 / Not Yet A Member: $3,360.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

This will be a hands-on training course. The extra cost is for materials.

Locations:

MANCHESTER NH - OSHA TRAINING INSTITUTE EDUCATION CENTER

Pipefitting 2 – ONLINE COURSE

This course consists of 159 classroom hours covering the following areas: Basic Safety; Introduction to Construction Math; Introduction to Hand Tools; Introduction to Power Tools; Introduction to Construction Drawings; Basic Rigging; Basic Communication Skills; Basic Employability Skills; Introduction to Materials Handling; Orientation to the Trade; Pipefitting Hand Tools; Pipefitting Power Tools; Oxyfuel Cutting; Ladder & Scaffolds; Motorized Equipment; Piping Systems; Drawing & Detail Sheets; Identifying & Installing Valves; Pipefitting Trade Math; Threaded Pipe Fabrication; Socket Weld Pipe Fabrications & Butt Weld Pipe Fabrication; Excavations; Underground Pipe Installations; Rigging Equipment; Rigging Practices;  Standards & Specifications;  Advanced Trade Math; Motorized Equipment II; Introduction to Aboveground Pipe Installations; Field Routing & Vessel Trim; Pipe Hangers & Supports; Testing Piping Systems & Equipment; Advanced Blueprint Reading; Advanced Pipe Fabrication; Stress Relieving & Aligning; Maintaining Valves; Introduction to Supervisory Roles

Begins September 9, 2026 – 5:00 – 8:00 PM – Mondays & Wednesdays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

VIRTUAL TRADE COURSE

Sheet Metal 1

This course consists of 159 classroom hours covering the following areas: Introduction to Sheet Metal; Basic Safety; Introduction to Hand Tools; Introduction to Power Tools; Introduction to B.G.L. c 112 s 237-251 and 271 CMR; Basic Rigging; Introduction to Materials Handling; Basic Communication Skills; Basic Employability Skills; Introduction to Construction Math; Introduction to Construction Drawings; Tools of the Trade; Installation of Ductwork.

September 8, 2026 – 5:00 – 8:00 PM – Tuesdays & Thursdays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

TAUNTON – BRISTOL-PLYMOUTH REGIONAL TECHNICAL SCHOOL

Carpentry 4 (Hands-On)

This course consists of 111 classroom hours covering the following areas: Site Layout One: Differential Leveling; Site Layout Two: Angular Distance and Measurement; Advanced Roof Systems; Advanced Wall Systems; Advanced Stair Systems; Introduction to Construction Equipment; Introduction to Oxyfuel Cutting and Arc Welding; Site Preparation; Fundamentals of Crew Leadership. 

Begins September 8, 2026
5:30 – 8:30 PM – Tuesdays & Thursdays

Tuition: $1,912.00

This will be a hands-on training course. The extra cost is for materials.

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

MEDFORD – MEDFORD VOCATIONAL TECHNICAL HIGH SCHOOL

Pipefitting 3

This course consists of 159 classroom hours covering the following areas: Steam Traps; In-Line Specialties; Special Piping; Hot Taps; Introduction to Hydronic Systems; Commercial Hydronic Systems; Steam Systems; Water Treatment; Energy Conservation Equipment; ASME Piping Codes for HVAC, Power and Process Piping 7.5; Semiconductor/Hazardous Gas Piping Systems 12.5;  Biopharma Piping Systems 12.5; Orbital Welding Fabrication 15; Chemical/Corrosion Resistant Piping Systems 15; Compressed Air Piping Systems

Begins September 8, 2026 – 5:00 – 8:00 PM – Tuesdays & Thursdays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

BILLERICA - GCI TRAINING FACILITY

Refrigeration Tech 3

This course consists of 159 classroom hours covering the following areas: Fasteners, Hardware, and Wiring Terminations; Control Circuit and Motor Troubleshooting; Troubleshooting Cooling; Troubleshooting Heat Pumps; Troubleshooting Gas Heating; Troubleshooting Oil Heating; Troubleshooting Accessories; Zoning Ductless, and Variable Refrigerant Flow Systems; Commercial Hydronic Systems; Steam Systems; Retail Refrigeration System; Customer Relations.

Begins September 8, 2026 – 5:00 – 8:00 PM – Tuesdays & Thursdays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

BILLERICA - GCI TRAINING FACILITY

Plumbing Tier 4

This course consists of 120 classroom hours covering the following areas: Business Principles for Plumbers; Fundamentals of Crew Leadership; Water Pressure Booster and Recirculation Systems; Indirect and Special Waste; Hydronic and Solar Heating Systems; Codes; Private Water Supply Well Systems; Private Waste-Disposal Systems; Swimming Pools and Hot Tubs; Plumbing for Mobile Homes and Travel Trailer Parks; Introduction to Medical Gas and Vacuum Systems.

Begins September 9, 2026 – 4PM – 7PM – Mondays & Wednesdays

Tuition: $1,924.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

SPRINGFIELD - SPRINGFIELD TECHNICAL COMMUNITY COLLEGE

Sprinklerfitting 4

This course consists of 160 classroom hours covering the following areas: System Layout; Inspection, Testing, and Maintenance; Special Extinguishing Systems; Introductory Skills for Foreman; Procedures and Documentation

September 8, 2026 – 5:00 – 8:00 PM – Tuesdays & Thursdays

ABC Member: $2,567.00 / Not Yet A Member: $3,360.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

TAUNTON – BRISTOL-PLYMOUTH REGIONAL TECHNICAL SCHOOL

Plumbing Tier 5

This course consists of 120 classroom hours covering the following areas: Review of all sections of the Massachusetts State Plumbing Code 248 CMR 3.00, 248 CMR 10.00, and 248 CMR 11.00; Review of all sections of NFPA-54-2012, NFPA-58-2011, Massachusetts Fuel Gas Code 248 CMR 4.00, Amendments for NFPA-54-2012 248 CMR 5.00, Large Gas Utilization Equipment 248 CMR 7.00 and Amendments to NFPA 58-2011 248 CMR 8.00; Review of all plumbing related math covered in Tier I through Tier V; review of all sketches in Massachusetts State Plumbing Code Section 10.22 Figures; Business Related Costs.

Begins September 8, 2026 – 4PM – 7PM – Tuesdays & Thursdays

Tuition: $1,924.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

SPRINGFIELD - SPRINGFIELD TECHNICAL COMMUNITY COLLEGE

Sheet Metal 2 (Hands-On)

This course consists of 159 classroom hours covering the following areas: Safety Review; Trade Math 104; Shop Production and Organization; Installation of Air Distribution Accessories; Air Systems; Duct Fabrication Standards; Introduction to Layout; Fabrication I – Parallel Line Development; Fabrication II – Radial Line Development; and Hands-on Shop Fabrication.

September 8, 2026 – 5:00 – 8:00 PM – Tuesdays & Thursdays

ABC Member: $2,817.00 / Not Yet A Member: $3,360.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

TAUNTON – BRISTOL-PLYMOUTH REGIONAL TECHNICAL SCHOOL

Plumbing Tier 3

This course consists of 120 classroom hours covering the following areas: Applied Math; Sizing and Protecting the Water Supply System; Potable Water Supply Treatment; Types of Venting; Sizing DWV and Storm Systems; Sewage Pumps and Sump Pumps; Corrosive-Resistant Waste Piping; Compressed Air; Service Plumbing.

Begins September 14, 2026 – 4PM – 7PM – Mondays & Wednesdays

Tuition: $1,924.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

SPRINGFIELD - SPRINGFIELD TECHNICAL COMMUNITY COLLEGE

Plumbing Tier 1

This course consists of 120 classroom hours covering the following areas: Basic Safety; Introduction to Construction Math; Introduction to Hand Tools; Introduction to Power Tools; Introduction to Construction Drawings; Basic Rigging; Basic Communication Skills; Basic Employability Skills; Introduction to Materials Handling; Introduction to Plumbing; Plumbing Safety; Tools of the Plumbing Trade; Introduction to Plumbing Math; Introduction to Plumbing Drawings; Plastic Pipe and Fittings; Copper Tube and Fittings; Cast-Iron Pipe and Fittings; Carbon Steel Pipe and Fittings; Introduction to Plumbing Fixtures; Introduction to Drain, Waste, and Vent (DWV) Systems.

Begins September 8, 2026 – 4PM – 7PM – Tuesdays & Thursdays

Tuition: $1,924.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

SPRINGFIELD - SPRINGFIELD TECHNICAL COMMUNITY COLLEGE

Sheet Metal 1

This course consists of 152 classroom hours covering the following areas: Introduction to Sheet Metal; Basic Safety; Introduction to Hand Tools; Introduction to Power Tools; Introduction to B.G.L. c 112 s 237-251 and 271 CMR; Basic Rigging; Introduction to Materials Handling; Basic Communication Skills; Basic Employability Skills; Introduction to Construction Math; Introduction to Construction Drawings; Tools of the Trade; Installation of Ductwork.

Begins September 9, 2026 – 5:00 – 9:00 PM – Mondays & Wednesdays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

*Schedule Update: Sheet Metal classes at our Billerica location will be held two nights per week for 4 hours per night with a shop sessions being scheduled on some Saturdays throughout the course. We will also hold classes during February and April school vacations.

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

BILLERICA - GCI TRAINING FACILITY

Electrical 1

This course consists of 152 classroom hours covering the following areas: Basic Safety; Introduction to Construction Math; Introduction to Hand Tools; Introduction to Power Tools; Introduction to Construction Drawings; Basic Rigging; Basic Communication Skills; Basic Employability Skills; Introduction to Materials Handling; Orientation to the Electrical Trade; Electrical Safety; Introduction to Electrical Circuits; Electrical Theory; Introduction to the National Electrical Code (NEC); Device Boxes; Hand Bending; Raceways and Fittings; Conductors and Cables; Basic Electrical Construction Drawings; Residential Electrical Services; Electrical Test Equipment. It is required that all students bring a copy of the National Electrical Code, 2026 Edition, with the Commonwealth of Massachusetts Amendments (527 CMR 12.00) to class.

Begins September 8, 2026 – 4:00 – 8:00 PM – Thursdays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

CANTON - GCI TRAINING SPACE AT PEC

Sheet Metal 2 (Hands-On)

This course consists of 152 classroom hours covering the following areas: Safety Review; Trade Math 104; Shop Production and Organization; Installation of Air Distribution Accessories; Air Systems; Duct Fabrication Standards; Introduction to Layout; Fabrication I – Parallel Line Development; Fabrication II – Radial Line Development; and Hands-on Shop Fabrication.

Begins September 8, 2026 – 5:00 – 9:00 PM – Tuesdays & Thursdays

ABC Member: $2,817.00 / Not Yet A Member: $3,360.00

*Schedule Update: Sheet Metal classes at our Billerica location will be held two nights per week for 4 hours per night with a shop sessions being scheduled on some Saturdays throughout the course. We will also hold classes during February and April school vacations.

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

This will be a hands-on training course. The extra cost is for materials.

Locations:

BILLERICA - GCI TRAINING FACILITY

Electrical 1

This course consists of 159 classroom hours covering the following areas: Basic Safety; Introduction to Construction Math; Introduction to Hand Tools; Introduction to Power Tools; Introduction to Construction Drawings; Basic Rigging; Basic Communication Skills; Basic Employability Skills; Introduction to Materials Handling; Orientation to the Electrical Trade; Electrical Safety; Introduction to Electrical Circuits; Electrical Theory; Introduction to the National Electrical Code (NEC); Device Boxes; Hand Bending; Raceways and Fittings; Conductors and Cables; Basic Electrical Construction Drawings; Residential Electrical Services; Electrical Test Equipment. It is required that all students bring a copy of the National Electrical Code, 2026 Edition, with the Commonwealth of Massachusetts Amendments (527 CMR 12.00) to class.

Begins September 8, 2026 – 6:00 – 9:00 PM – Tuesdays & Thursdays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

MEDFORD – MEDFORD VOCATIONAL TECHNICAL HIGH SCHOOL

Sheet Metal 3 (Hands-On)

This course consists of 152 classroom hours covering the following areas: Trade Math II; Introduction to Supervisory Skills; Air Properties and Distribution; Principles of Airflow; Air Testing and Balancing; Fabrication III – Triangulation; Plans and Specifications; and Hands-on Shop Fabrication.

Begins September 9, 2026 – 5:00 – 9:00 PM – Mondays & Wednesdays

ABC Member: $2,817.00 / Not Yet A Member: $3,360.00

*Schedule Update: Sheet Metal classes at our Billerica location will be held two nights per week for 4 hours per night with a shop sessions being scheduled on some Saturdays throughout the course. We will also hold classes during February and April school vacations.

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

This will be a hands-on training course. The extra cost is for materials.

Locations:

BILLERICA - GCI TRAINING FACILITY

Electrical 4

This course consists of 152 classroom hours covering the following areas: Load Calculations –Feeders and Services; Health Care Facilities; Standby and Emergency Systems; Basic Electronic Theory; Fire Alarm Systems; Specialty Transformers; Advanced Controls; HVAC Controls; Heat Tracing and Freeze Protection; Motor Operation and Maintenance; Medium-Voltage Terminations/Splices; Special Locations; Fundamentals of Crew Leadership. It is required that all students bring a copy of the National Electrical Code, 2026 Edition, with the Commonwealth of Massachusetts Amendments (527 CMR 12.00) to class.

Begins September 14, 2026 – 4:00 – 8:00 PM – Mondays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

CANTON - GCI TRAINING SPACE AT PEC

Refrigeration Tech 3

This course consists of 159 classroom hours covering the following areas: Fasteners, Hardware, and Wiring Terminations; Control Circuit and Motor Troubleshooting; Troubleshooting Cooling; Troubleshooting Heat Pumps; Troubleshooting Gas Heating; Troubleshooting Oil Heating; Troubleshooting Accessories; Zoning Ductless, and Variable Refrigerant Flow Systems; Commercial Hydronic Systems; Steam Systems; Retail Refrigeration System; Customer Relations.

Begins September 8, 2026 – 5:00 – 8:00 PM – Tuesdays & Thursdays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

TAUNTON – BRISTOL-PLYMOUTH REGIONAL TECHNICAL SCHOOL

Sheet Metal 5 (Hands-On)

This course consists of 152 classroom hours covering the following areas: Trade Math – Estimating; Fume Exhaust Design; Introduction to Welding, Brazing and Cutting; Advanced Architectural Sheet Metal; Hands-on Shop Fabrication; and Exam Review and Preparation.

September 9, 2026 – 5:30 – 8:30 PM – Mondays & Wednesdays

ABC Member: $2,817.00 / Not Yet A Member: $3,360.00

*Schedule Update: Sheet Metal classes at our Billerica location will be held two nights per week for 4 hours per night with a shop sessions being scheduled on some Saturdays throughout the course. We will also hold classes during February and April school vacations.

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

This will be a hands-on training course. The extra cost is for materials.

Locations:

MANCHESTER NH - OSHA TRAINING INSTITUTE EDUCATION CENTER

Electrical 3

This course consists of 152 classroom hours covering the following areas: Load Calculations – Branch and Feeder Circuits; Conductor Selection and Calculations; Practical Applications of Lighting; Hazardous Locations; Overcurrent Protection; Distribution Equipment; Transformers; Commercial Electrical Services; Motor Calculations; Voice, Data, and Video; Motor Controls. It is required that all students bring a copy of the National Electrical Code, 2026 Edition, with the Commonwealth of Massachusetts Amendments (527 CMR 12.00) to class.

Begins September 9, 2026
4:00 PM – 8:00 PM – Wednesdays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

CANTON - GCI TRAINING SPACE AT PEC

Electrical 2

This course consists of 152 classroom hours covering the following areas: Alternating Current; Motors: Theory and Application; Electric Lighting; Conduit Bending; Pull and Junction Boxes; Conductor Installations; Cable Tray; Conductor Terminations and Splices; Grounding and Bonding; Circuit Breakers and Fuses; Control Systems and Fundamental Concepts. It is required that all students bring a copy of the National Electrical Code, 2026 Edition, with the Commonwealth of Massachusetts Amendments (527 CMR 12.00) to class.

Begins September 8, 2026
4:00 PM – 8:00 PM – Tuesdays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

CANTON - GCI TRAINING SPACE AT PEC

Sheet Metal 4 (Hands-On)

This course consists of 152 classroom hours covering the following areas: Massachusetts Uniform Sheet Metal Code; Trade Math III – Field Measuring; Comprehensive Plan and Specification Reading; Soldering; Architectural Sheet Metal; Louvers, Dampers and Access Doors; Fabrication IV – Comprehensive Review; and Hands-on Shop Fabrication.

Begins September 8, 2026 – 5:00 – 9:00 PM – Tuesdays & Thursdays

ABC Member: $2,817.00 / Not Yet A Member: $3,360.00

*Schedule Update: Sheet Metal classes at our Billerica location will be held two nights per week for 4 hours per night with a shop sessions being scheduled on some Saturdays throughout the course. We will also hold classes during February and April school vacations.

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

This will be a hands-on training course. The extra cost is for materials.

Locations:

BILLERICA - GCI TRAINING FACILITY

Sheet Metal 4 (Hands-On)

This course consists of 159 classroom hours covering the following areas: Massachusetts Uniform Sheet Metal Code; Trade Math III – Field Measuring; Comprehensive Plan and Specification Reading; Soldering; Architectural Sheet Metal; Louvers, Dampers and Access Doors; Fabrication IV – Comprehensive Review; and Hands-on Shop Fabrication.

September 8, 2026 – 5:00 – 8:00 PM // Tuesdays & Thursdays

ABC Member: $2,817.00 / Not Yet A Member: $3,360.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

This will be a hands-on training course. The extra cost is for materials.

Locations:

TAUNTON – BRISTOL-PLYMOUTH REGIONAL TECHNICAL SCHOOL

Electrical 4

This course consists of 159 classroom hours covering the following areas: Load Calculations –Feeders and Services; Health Care Facilities; Standby and Emergency Systems; Basic Electronic Theory; Fire Alarm Systems; Specialty Transformers; Advanced Controls; HVAC Controls; Heat Tracing and Freeze Protection; Motor Operation and Maintenance; Medium-Voltage Terminations/Splices; Special Locations; Fundamentals of Crew Leadership. It is required that all students bring a copy of the National Electrical Code, 2026 Edition, with the Commonwealth of Massachusetts Amendments (527 CMR 12.00) to class.

Begins September 8, 2026 – 5:30 – 8:30 PM – Tuesdays & Thursdays

ABC Member: $2,567.00 / Not Yet A Member: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

MEDFORD – MEDFORD VOCATIONAL TECHNICAL HIGH SCHOOL

Electrical Masters

This 168 hours Certified Program as per requirements contained in “237 CMR 22.02: Required Electrical Education as a Prerequisite for Master Electrician Examination” will focus the attention of the Eligible Candidate to the current testing edition of the National Electrical Code (NFPA 70-2020) with particular attention also given to the Commonwealth of Massachusetts Electrical Code Amendments (527 CMR 12:00) as contained in the current edition of the National Electrical Code (NFPA 70-2020) and other required documents and information required to sit for the test.

This course is intended to supplement the continuing studies of the serious Eligible Candidate, with emphasis on assisting the Eligible Candidate to pass the desired Commonwealth of Massachusetts, Certificate A (Master) Electrician License Examination. It is required that all students bring a copy of the National Electrical Code, 2026 Edition, with the Commonwealth of Massachusetts Amendments (527 CMR 12.00) to class.

Begins September 9, 2026 – 5:30 PM – 8:30 PM – Mondays & Wednesdays
Tuition Price: $2,910.00 + $265.00 optional book fee

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

SPRINGFIELD - SPRINGFIELD TECHNICAL COMMUNITY COLLEGE

Electrical 4

This course consists of 168 classroom hours covering the following areas: Load Calculations –Feeders and Services; Health Care Facilities; Standby and Emergency Systems; Basic Electronic Theory; Fire Alarm Systems; Specialty Transformers; Advanced Controls; HVAC Controls; Heat Tracing and Freeze Protection; Motor Operation and Maintenance; Medium-Voltage Terminations/Splices; Special Locations; Fundamentals of Crew Leadership. It is required that all students bring a copy of the National Electrical Code, 2026 Edition, with the Commonwealth of Massachusetts Amendments (527 CMR 12.00) to class.

Begins September 8, 2026 – 6:00 – 9:00 PM – Tuesdays & Thursdays

Tuition: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

SPRINGFIELD - SPRINGFIELD TECHNICAL COMMUNITY COLLEGE

Electrical 3

This course consists of 168 classroom hours covering the following areas: Load Calculations – Branch and Feeder Circuits; Conductor Selection and Calculations; Practical Applications of Lighting; Hazardous Locations; Overcurrent Protection; Distribution Equipment; Transformers; Commercial Electrical Services; Motor Calculations; Voice, Data, and Video; Motor Controls. It is required that all students bring a copy of the National Electrical Code, 2026 Edition, with the Commonwealth of Massachusetts Amendments (527 CMR 12.00) to class.

Begins September 8, 2026 – 6:00 – 9:00 PM – Tuesdays & Thursdays

Tuition: $3,110.00

Note: All tuition must be paid in full at the time of registration in order to guarantee your student’s place in their selected class. With limited space available, our classes tend to fill up quickly, so we strongly encourage you to plan ahead and ensure that tuition is paid on time.

Locations:

SPRINGFIELD - SPRINGFIELD TECHNICAL COMMUNITY COLLEGE

NINE CONVENIENT LOCATIONS

    Billerica | Canton | Manchester, NH      Medford | North Adams  | Plymouth    Springfield | Taunton | Woburn

OR ONLINE

OUR PARTNERS

Wentworth Institute of Technology
Springfield Technical Community College
Penn Foster

READ MORE

Turn to the Gould Construction Institute for high quality cost-effective training.